Volkswagen’s turbocharged 2.0T TSI engine requires the correct engine oil, filter design, and service components to maintain reliable lubrication and protect internal engine parts.
This guide covers select Volkswagen GTI, Jetta, Tiguan, CC, Eos, Beetle, and Passat models equipped with compatible CCTA or CBFA engines and a 06J 115 403 Q-style spin-on oil filter.
Compatible Volkswagen Models
The VW GTI, Jetta and Tiguan 2.0T Liqui Moly 5W-40 Oil Change Kit supports the following applications:
| Year | Model | Engine | Fuel |
|---|---|---|---|
| 2012–2013 | Volkswagen Beetle Turbo | 2.0L TSI – CCTA/CBFA | Gasoline |
| 2009–2017 | Volkswagen CC | 2.0L TSI – CCTA/CBFA | Gasoline |
| 2009–2016 | Volkswagen Eos | 2.0L TSI – CCTA/CBFA | Gasoline |
| 2008–2014 | Volkswagen GTI | 2.0L TSI – CCTA/CBFA | Gasoline |
| 2008–2013 | Volkswagen Jetta / GLI | 2.0L TSI – CCTA/CBFA | Gasoline |
| 2008–2010 | Volkswagen Passat | 2.0L TSI – CCTA | Gasoline |
| 2009–2017 | Volkswagen Tiguan | 2.0L TSI – CCTA/CBFA | Gasoline |
Why Use Liqui Moly Leichtlauf High Tech 5W-40?
Liqui Moly Leichtlauf High Tech 5W-40 is formulated for modern gasoline and diesel engines operating under demanding conditions. Its VW 502 00 specification makes it suitable for the gasoline-powered Volkswagen 2.0T applications covered by this guide.
The oil supports:
- Rapid lubrication during cold starts
- Stable oil pressure at operating temperature
- Turbocharger protection
- Resistance to oxidation and aging
- Engine cleanliness
- Wear protection under demanding driving conditions
Why the Oil Filter Design Matters
This engine family uses a threaded spin-on oil filter rather than the cartridge filter found on many later Volkswagen engines.
The included Hengst H14W30 filter corresponds to OE reference 06J 115 403 Q. Ordering by model name alone can result in the wrong filter because some Volkswagen model years transitioned between engine generations.
Always verify the engine code and existing filter design before ordering.
What’s Included?
- Five liters of Liqui Moly Leichtlauf High Tech 5W-40
- Hengst H14W30 spin-on oil filter
- Replacement engine-oil drain plug
- Drain-plug sealing washer
General Oil Change Procedure
- Warm the engine slightly and park on a level surface.
- Open the hood and remove the oil filler cap.
- Safely raise and support the vehicle where necessary.
- Position an appropriate drain pan beneath the engine.
- Remove the old drain plug and allow the oil to drain.
- Remove the existing spin-on oil filter.
- Clean the filter mounting surface.
- Lightly lubricate the new filter seal with fresh oil.
- Install the Hengst filter according to its service instructions.
- Install the replacement drain plug and sealing washer.
- Add the initial quantity of fresh engine oil.
- Start the engine briefly and inspect for leaks.
- Switch off the engine and allow the oil to settle.
- Verify the final level and add oil gradually when required.
- Reset the oil-service reminder if applicable.
Never rely only on the container size as the engine’s exact fill quantity. Confirm the final oil level using the approved procedure for your vehicle.
Confirm Fitment Before Ordering
Verify that:
- The vehicle appears in the fitment table.
- The engine code is CCTA or CBFA.
- The engine requires VW 502 00-compatible oil.
- The existing filter is a spin-on design.
- The filter cross-references to 06J 115 403 Q.
Order the complete Liqui Moly 5W-40 Volkswagen 2.0T oil change kit with Hengst filter from SayParts.